Znaleziono w kategoriach:
Konsole dj (4)
Wróć
MIX 2
User manual
Instrukcja obsługi
ENGLISH
A. STRUCTURE AND FEATURES
1. [MIC/LINE]:
Mono input socket, you can connect XLR plug and phone plug to connect the microphone or instru-
ment you want to use.
2. [MAIN OUTPUT]:
TRS phone type unbalanced output socket for outputting mixed stereo signal. The signal level can be
adjusted through the [MAIN] knob before being output. For example, these sockets can be used to
connect the power amplifier.
3. +48V PHANTOM power switch.
Turn off / Turn on, when using a condenser microphone powered by phantom power, turn on
the switch. Notice: The phantom power supply only supplies power to XLR plugs connected to channel
1 and 2 sockets. If you do no need phantom power, be sure to set this switch to off ( ). When the
phantom power is turned on ( ), pay attention to the following rules to prevent noise or damage to
the mixer or external equipment: Do not disconnect the XLR plug when the switch is on. Before turning
on and off the phantom power supply, set the output controller such as [MAIN] to the minimum level.
4. [HI-Z]: INPUT2 signal input mode switching.
Line input mode / Instrument input mode. When connecting high impedance appliances, such
as electric guitar or electric bass, you need to turn on instrument input mode by pressing [HI-Z] button.
5. 3.5mm microphone interface.
The interface suitable for 3V condenser microphone. The level signal is adjusted by 1-channel volume
controller and sent to [MAIN] mixed output.
6. [PEAK] indicator light.
When the input signal reaches 3dB of clipping distortion, the indicator will light up. Adjust the channel
volume knob to make the [PEAK] indicator light flash briefly for the best recording level.
7. [SIG] indicator light.
When the input signal is higher than 3dB of clipping distortion, the indicator light will be on. Setting
the best recording level requires adjusting the channel volume knob to make the [PEAK] indicator
light flash briefly.
8. [ST PAN]: mono/stereo switch.
When channel 1 and 2 respectively input independent signals, it is necessary to switch to mono state
( ). When stereo signal is input, it is necessary to switch to stereo state ( ). At this time, channel
1 volume knob control the output level of left channel and channel 2 volume knob control the output
level of right channel.
9. [LEVEL]:
Channel volume control knob, which can control the channel output level and send it to [MAIN] mixed
output.
10. [MAIN]:
Adjust the signal level of the [MAIN OUTPUT] socket.
11. [PHONES]:
Adjust the output level signal of the monitoring headphone socket.
12. [+48V] indicator light.
The indicator lights up when the phantom power switch is turned on.
13. Power indicator.
The power indicator lights up when the power supply is connected.
14. Headphone monitoring socket.
For connecting a pair of 3.5 mm plugs of stereo headphones.
15. [REC]: computer recording signal selection switch.
( ) When it pops up, the sound source recorded by the computer is the level signal output by chan-
nels 1 and 2. ( ) When it is pressed, the sound source recorded by the computer is a mixed signal
(the level signal played by the computer + the level signal output by channels 1 and 2).
16. Type B USB 2.0 port.
It is used to connect a computer to transfer data and provide power to the device at the same time.
Note: When connecting the computer, please pay attention to the following points – failure to do so
may cause the computer to crash and cause data loss or destruction: If the mixer and computer crash,
disconnect the devices by unplugging the cable from the computer, restart the application or com-
puter, and then reconnect the cable to the computer. Wait at least 5 seconds between disconnect-
ing/reconnecting the cable.
B. OPERATION
1. Connect the mixer to the device of choice using the supplied USB cable, taking precautions. If the
mixer is connected to a computer, the computer should automatically detect the device and install the
drivers.
2. The power indicator on the mixer will light up.
3. The features of the mixer are described in the STRUCTURE AND FEATURES section.
4. After using the mixer, disconnect it from the device of choice by pulling the plug of the USB power
cable and taking precautions.
C. INFORMATION ABOUT USED ELECTRICAL AND ELECTRONIC EQUIP-
MENT
WARNING! THE DEVICE MUST NOT BE DISPOSED OF WITH HOUSEHOLD WASTE.
This symbol indicates that this product must not be disposed of with household waste, according to
the EU and your national law. In order to prevent potential damage to the environment or health, the
used product must be recycled. In accordance with current legislation, unusable electrical and elec-
tronic devices must be collected separately at the designated facilities for recycling, acting on the
basis of applicable environmental standards.
The main goal of European and national law regulations is to reduce the amount of waste produced
from used electrical and electronic equipment, to ensure an appropriate level of collection, recovery
and recycling of used equipment, and to increase public awareness of its harmfulness to the environ-
ment, at each stage of use of electrical and electronic equipment. Therefore, it should be pointed out
that households play a key role in contributing to reuse and recovery, including recycling of used
equipment. The user of electrical and electronic equipment – intended for households – is obliged to
return it to authorized collector after its use. However, it should be remembered that products classi-
fied as electrical or electronic equipment should be disposed of at authorized collection points.
POLSKI
A. BUDOWA I FUNKCJE
1. [MIC/LINE]:
Gniazdo wejściowe mono, do którego można podłączyć wtyczkę XLR lub wtyczkę jack 6,3 mm w celu
podłączenia mikrofonu lub instrumentu,
2. [MAIN OUTPUT]:
Niezbalansowane gniazdo wyjściowe TRS (6.3 mm jack) do wyprowadzania zmiksowanego sygnału
stereo. Poziom sygnału można regulować za pomocą pokrętła [MAIN] przed wyjściem. Gniazda te
mogą być na przykład używane do podłączania wzmacniacza mocy.
3. Przełącznik zasilania +48V PHANTOM.
Wył. / wł., w przypadku korzystania z mikrofonu pojemnościowego zasilanego napięciem
Phantom należy włączyć przełącznik. Uwaga: Zasilanie Phantom dostarcza zasilanie tylko do wty-
czek XLR podłączonych do gniazd kanałów 1 i 2. Jeśli zasilanie Phantom nie jest potrzebne, należy
ustawić ten przełącznik w pozycji wyłączonej ( ). Gdy zasilanie Phantom jest włączone ( ), należy
zwrócić uwagę na następujące zasady, aby zapobiec zakłóceniom lub uszkodzeniu miksera bądź
urządzenia zewnętrznego: Nie odłączaj wtyczki XLR, gdy przełącznik jest włączony. Przed włącze-
niem i wyłączeniem zasilania Phantom należy ustawić poziom wyjścia, taki jak [MAIN], na minimalny
poziom.
4. [HI-Z]: przełączanie trybu wejścia sygnału INPUT2.
Tryb wejścia liniowego / tryb wejścia instrumentu. W przypadku podłączania urządzeń o wy-
sokiej impedancji, takich jak gitara elektryczna lub elektryczny bas, należy włączyć tryb wejścia in-
strumentu, naciskając przycisk [HI-Z].