-50% na wybrane usługi i 100 dni na zwrot!
Znaleziono w kategoriach:
BC3010/5010
Електрическа коса
Elektrický krovinorez
Ηλεκτρικό δρεπάνι
Elektrivikat
Električna kosa
Elektriskais izkapts
Kosa elektryczna
Brush cutter
Električna kosilnica
Elektrinis dalgis
Elektrická kosa
Elektromos fűkasza
Coasă electrică
1
16
3
15
2
14 45
7
6
9
11
12 10
13
8
BC3010/5010
BC3010
1
1
16
3
15
214 4
5
7
6
9
11
12 10
13
8
BC5010
BC3010/5010
2
11
GRASS mowing:
Do not mow wet grass. The best mowing results are achieved when the grass is dry. Insert the
extension cord through the back of the arm, making sure that it is always behind the user when
cutting.
Keep the device tilted at an angle of 20 degrees to the grass being mowed, moving it in a pendulum
motion, to the left and right. Make sure to keep the device away from yourself – see figure.
Effective mowing of the grass with the device is possible only if the grass not higher than 15 cm. Keep
the grass trimmer away from hard objects. When the string or blade comes into contact with a hard
object, the string or blade may break. Stones can be thrown away and hit the surrounding objects at
high speed causing damage. It is prohibited to use the device without a safety cover.
When using the trimmer, remember to maintain proper body posture during work.
MOWING AROUND SHRUBS AND TREES
When mowing grass and weeds around shrubs and trees be extremely careful and do not allow them to
come into contact with the rotating string or blade. Damage to the bark may result in the death of the
tree or shrub .
String ejection:
If the string is too short, pull it out. The unit is equipped with an automatic dispense head. Press the
reel lightly against the ground to eject the string automatically.
During this operation, please note that pressing the reel too hard or too hard against the ground may
cause damage to the reel, so it is recommended to do it manually to prevent damage.
Cleaning and maintenance
1. After each use clean the entire device of plant residues and the lower cover of the collected
compacted mass.
2. Ventilation slots and motor housing should be kept free of dust and dirt, as much as possible. Wipe
the device with a clean cloth, brush or purge with compressed air.
3. It is recommended to clean immediately after every use.
4. Do not use any cleaning agents or solvents to clean the device; they may damage the plastic parts.
Take care not to allow water to enter the device.
5. Check the condition of the cutting string regularly, as well as the
BC3010/5010
12
tightening of the screws. With new devices, the bolt tightening should be checked after about 2 first
hours of operation. Tighten the loosened bolts if necessary.
6. Ensure that all components of the power tool are in good working order and do not overload or carry
out any work for which the device is not intended
Brush cutter
Motor type: electric, brush
Motor power: 1400 W
Rotational speed: 7500 rpm
Cutting diameter of the string: 420 mm
Type and type of head: semi-automatic/double string
Recommended string diameter: from 1.6 mm to 2.0 mm
Noise and vibrations.
The noise and vibrations have been measured in accordance with 2000/14/EC, 2005/88/EC .
Noise emission: Sound pressure level (LpA): 75.51 dB (A)
KpA deviation: 3,00 dB (A)
Measured sound power level LwA: 95.51 dB (A)
KwA deviation: 0.93 dB (A)
Guaranteed sound power level: LwA: 96.00 dB (A)
Total vibration value and measurement uncertainty (K):
The value of vibrations acting on the upper limbs: 7.95 m/s² , k=1.5 m/s²
The declared total vibration value has been measured according to the standard test method and can
be used to compare
one device to another. The given vibration emission value may be used for the preliminary estimation
of the negative impact.
After every 15 minutes of work allow 15 minutes break.
BC3010/5010
