-50% na wybrane usługi i 100 dni na zwrot!
Znaleziono w kategoriach:
3402125000_31-P5734_00_01_WEB 80 × 120 mm zdroj: 3402125000_31-P5734_00_01.indd
www.emos.eu
P5734
P5734B
GB Wireless Doorchime
CZ Bezdrátový zvonek
SK Bezdrôtový zvonček
PL Dzwonek bezprzewodowy
HU Vezeték nélküli csengő
SI Brezžični zvonec
RS|HR|BA|ME Bežično zvono
DE Drahtlose Klingel
UA Бездротовий дзвоник
RO|MD Sonerie fără r
LT Belaidis durų skambutis
LV Bezvadu durvju zvans
EE Juhtmeta uksekell
BG Безжичен звънец
FR Carillon sans l
IT Campanello senza li
ES Timbre inalámbrico
NL Draadloze deurbel
2
1
2 3
3
44
1
2
4
5
1
2
3
1
3
4
GB | Wireless Doorchime
The set consists of a doorbell button (transmitter) and a chime (receiver). The
chime is designed for constant connection to a 230 V AC/50 Hz power grid.
Transmission between the button and the chime is carried via radio waves at
a frequency of 433.92 MHz. The range depends on local conditions and reaches
up to 150 m in an open area without interference.
The set has a so-called self-learning function – the button is able to generate
its own pairing code which is then received by the chime and stored in its
memory. The set can thus be expanded with additional buttons. The function
also prevents the set from aecting neighbouring doorbells.
For proper use of the wireless doorbell, read the instruction manual thoroughly.
Technical Specications
Transmission range: up to 150 m in an open area (can drop down to one fth
in a busy area)
Button: water resistant; enclosure rating IP56
Pairing the chime with buttons: self-learning function
Pairing capacity: maximum of 8 buttons per 1 chime
Number of ringtones: 10
Transmission frequency: 433.92 MHz, 10 mW e.r.p. max.
Chime power supply: 230 V AC/50 Hz
4
Button power supply: 1× 3 V battery (type CR2032, included)
Includes: double-sided adhesive tape
Chime Description (see g. 1)
1 – bell LEDs
2 – speaker
3 – volume setting button
4 – ringtone setting button
Button Description (see g. 2)
1 – ring button
2 – LED
3 – nameplate cover
4 – hole for opening the battery
cover
5 – mounting pad
Installing the Button/Removing the Mounting Pad (see g. 3)
1 – holes for screws
Changing the Button’s Battery (see g. 4)
Pairing the Button with the Chime
1. Plug the chime unit into a 230 V AC/50 Hz socket.
2. Then, long-press the pairing button on the chime for ca. 5 seconds.
3. The chime LED will light up; release the button. The chime will switch
to self-learning pairing mode which lasts for 25 seconds. During this time,
press the ring button. The chime will ring and the button is now paired with
the chime. This automatically ends self-learning mode.
4. To pair multiple buttons, repeat the process for each button from step 1.
Note: The chime has an internal memory where it stores the codes of the
currently paired buttons for the event of a power failure. There is thus no need
to pair buttons again after a power cut.
Wiping the Memory of Paired Buttons
Press and hold the pairing button on the chime.
Plug the chime into a socket.
The LED of the chime will light up after ca. 5 seconds. Release the button.
The LED will turn o.
The memory of all paired buttons will be erased.
Selecting a Ringtone
1. Repeatedly press the ringtone setting button or located on the chime.
2. Each press of the button will play a dierent ringtone. The last ringtone
played is the one that will be used.
Setting the Bell Volume
You can set 5 volume levels.
Repeatedly press the button on the chime. Each press changes the volume
level (100 % – 75 % – 50 % – 25 % – 0 %). At 0 %, ringing is indicated only by
the bell LED ashing.
5
Installing the Doorbell Button (Transmitter)
1. Begin by pairing the button with the chime.
2. Before installation, check that the pair works reliably in the chosen spot.
3. Remove the mounting pad from the battery cover, see the g. 3.
4. Use the double-sided adhesive tape (included) or two screws (not
included) to x the back of the mounting pad to the wall. Although the
button is weather resistant, choose a location where it is protected, e.g.
in a wall recess.
5. Fit the mounting pad back onto the button.
6. Press the button to ring the chime. Pressing is accompanied by LED
illumination indicating the button has sent a radio signal. The chime plays
the selected ringtone.
Note: The doorbell button (transmitter) can be placed on wood or brick walls
without issue. However, never place the button directly onto metal objects or
materials containing metal, such as plastic windows or doors that have a metal
frame. In such cases, the transmitter will not work properly.
Installing the Chime (Receiver)
1. The doorbell is intended for indoor use only. When running, it must be
plugged in a 230 V AC/50 Hz socket and with free space around it so that
it is always accessible.
2. The transmission range (max. 150 m) is inuenced by local conditions,
such as the number of walls through which the signal passes, metal door
frames and other elements which aect the transmission of radio signals
(presence of other radio devices operating at a similar frequency, such
as wireless thermometers, gate controls etc.). Transmission range can
decrease drastically due to these factors.
Troubleshooting
The chime does not ring:
• The chime may be out of range.
• Change the distance between the button and the chime; the range may
be aected by local conditions.
• The button battery may be drained.
• Replace the battery. Make sure it has the correct polarity. Pair the
button with the chime again.
• The chime is not powered.
• Make sure the chime is properly plugged into the socket and that power
is on or the fuse/circuit breaker for the branch is on.
Upkeep and Maintenance
The wireless digital doorchime is a sensitive electronic device. Therefore, it is
necessary to observe the following precautions:
• The chime (receiver) is designed for indoor use in dry environments only.
