r
I www.russellhobbs.com
24650-56
GB
DE
FR
NL
IT
ES
PT
DK
SE
NO
FI
RU
CZ
SK
PL
HR
SI
GR
HU
TR
RO
BG
AE
2
l
k
m
fj
g
max
i
e
max
n
max
H B
3
Read the instructions, keep them safe, pass them on if you pass the iron on.
IMPORTANT SAFEGUARDS
Follow basic safety precautions, including:
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been supervised/instructed and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be done by children
unless they are older than 8 and supervised. Use and store the appliance
out of reach of children under 8 years.
Use the iron, or set it on its heel, on a stable, level, heat-resistant surface,
preferably an ironing board.
Don’t leave the iron unattended while plugged in, or while it’s standing on
the ironing board.
Unplug the iron before filling, before cleaning, and after use.
Don’t operate the appliance if it’s dropped or damaged, or if it
malfunctions or leaks.
If the cable is damaged, return the iron in order to avoid a hazard.
h The surfaces of the appliance will get hot during use.
b Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
• Never iron clothing while it is being worn.
• Don’t use the appliance for any purpose other than those described in these instructions.
• Don’t scratch the soleplate – avoid buttons, zips, etc.
• The appliance has a protective thermal fuse which will blow if it overheats. If this happens, the
appliance will stop working, and must be returned for repair.
HOUSEHOLD USE ONLY
PARTS
1. Temperature control
2. Soleplate
3. Heel
4. Light
5. Steam control
6. Water inlet
7. Cover
8. Spray nozzle
9. Mark
BEFORE USING FOR THE FIRST TIME
• Remove labels, stickers and packaging from the iron and soleplate.
• Don’t worry if the iron smokes a little at first. It will stop after a short time.
• Iron an old piece of cotton fabric, to clean the soleplate.
GB
DE
FR
NL
IT
ES
PT
DK
SE
NO
FI
RU
CZ
SK
PL
HR
SI
GR
HU
TR
RO
BG
AE
4
AUTO SHUT-OFF
• If the iron is motionless, it will switch off after about 30 seconds with the soleplate down or on its
side, or about 8 minutes if it’s upright.
• The light will flash and keep flashing till you move the iron.
• To switch on again, lift it up, tilt it forward, then sit it upright to return to operating temperature.
• No settings are lost during auto shut-off.
PREPARATION
1. Check for textile care symbols (i j k l).
2. Iron fabrics needing low temperatures j first, then those that need medium temperatures k, and
finish with those needing high temperatures l.
TEMPERATURE SETTING GUIDE
Label marking Dot setting
j cool – nylon, acrylics, polyester •
k warm – wool, polyester mixtures ••
l hot – cotton, linen •••
Max – denim max
i do not iron -
If the instructions on the fabric label differ from this guide, follow the instructions on the label.
FILLING
You may use the iron with tap-water, but if you live in a hard water area, you should use distilled water (not
chemically descaled or softened water).
If you buy distilled water, check that it’s suitable for use in irons.
1. Set the temperature control to • and set the steam control to S.
2. Unplug the iron.
3. Hold the iron with the front raised.
4. Open the water inlet cover.
5. Pour slowly, to let the air in the reservoir escape, otherwise you’ll cause an air lock and the water will
overflow.
6. Don’t fill past the max marking or water will escape in use.
7. Wipe up any spillage.
SWITCH ON
1. Set the temperature control to • and set the steam control to S.
2. Stand the iron on its heel.
3. Put the plug into the power socket (switch the socket on, if it’s switchable).
4. Turn the temperature control to bring the setting you want next to the marker. The light will come on.
5. When the iron reaches the temperature you set, the light will go out. It’ll then cycle on and off as the
thermostat operates to maintain the temperature.
STEAM IRONING
1. To steam iron, set the temperature control to S or higher.
2. Set the steam control to the setting you want, S = no steam, S = high steam.
5
3. Wait till the light goes out, then start ironing.
SPRAY
Water spotting affects some fabrics. Test this out on a hidden part of the fabric.
1. Lift the iron off the fabric.
2. Aim the spray nozzle at the fabric.
3. Press the ? button. You may have to press it 2 or 3 times to pump water through the system.
SHOT OF STEAM
1. Check that the temperature control is at S or higher.
2. Lift the iron off the fabric.
3. Press the hbutton.
• Leave 4 seconds between shots to let the temperature build up.
DRY IRONING
1. If you’re going to be dry ironing for 20 minutes or more, empty the reservoir first to avoid
spontaneous bursts of steam.
2. Set the steam control to S.
3. Set the desired temperature.
4. Wait till the light goes out, then start ironing.
VERTICAL STEAMING
Remove wrinkles from hanging clothes, hanging curtains, and furnishing fabrics.
• Check that there’s adequate ventilation behind the fabric, otherwise moisture may build up, causing
mildew.
• Check that there’s nothing behind the fabric that may be damaged by the steam.
• Check that pockets, turn-ups, and cuffs are empty.
• Check that there’s water in the reservoir.
1. Set the temperature control to max and set the steam control to S.
2. Hold the iron close to (but not touching) the fabric.
3. Press the hbutton.
• Leave 4 seconds between shots, to let the temperature build up.
AFTER USE
1. Set the temperature control to • and set the steam control to S.
2. Unplug the iron.
3. Open the water inlet cover.
4. Hold the iron over a sink, turn it upside down and drain the water from the reservoir.
5. Close the cover.
6. Sit the iron on its heel. Leave it to cool down completely.
7. When it’s cold, wipe off any moisture, and wind the cable round the heel.
8. Clean the outside surfaces of the appliance with a damp cloth.
9. Remove spots from the soleplate with a little vinegar.
10. Store the iron on its heel, to avoid corrosion and damage to the soleplate.
SELF CLEAN
To avoid scale build up, use the self clean function at least monthly in normal water areas, more often in
hard water areas.
You’ll need a basin or a large bowl to catch the water coming out of the soleplate.
GB
DE
FR
NL
IT
ES
PT
DK
SE
NO
FI
RU
CZ
SK
PL
HR
SI
GR
HU
TR
RO
BG
AE