Znaleziono w kategoriach:
Nianie elektroniczne (10)
Wróć
1
INSTRUCTIONS FOR USE
NannyCam H32 Pro
1
PACKAGE CONTENTS:
–Parent Unit (with display) + power adapter
–Baby Unit (camera) + power adapter
–Instructions for Use
BABY UNIT OVERVIEW:
1. Light Sensor
2. Camera Lens
3. Blue LED Power Indicator
4. Microphone
5. Infrared LED for night vision
6. Power Key – turn camera on/o
7. Power Adapter Connector
8. Thermal Sensor
9. Reset Button for pairing
10. Speaker
2
1
34
5
6
7
89
10
nnector
2
10
1
3456
7
8
9
11
13
12
14
PARENT UNIT OVERVIEW:
1. Power Switch (screen on/o)
2. Power Input / Battery Charging
3. LCD Display
4. Microphone
5. Blue LED - indicates device is on
6. Red LED - indicates connection with camera
7. VOX Mode (on/o)
8. Melody (on / o), two-way
communication (required
to hold for the entire talking
time)
9. 2× zoom
10. Speaker
11. OK / Menu Key
12. Back button / screen o
13. Volume +
14. Volume -
2
GETTING STARTED:
A) Baby Unit (camera)
1. Connect the small plug of the power adapter to the baby unit and the other end to the
mains socket.
2. Next slide the power switch to the “ON” position.
3. The blue LED indicates the camera is functioning correctly.
Note: Baby Unit requires a constant connection to the mains.
B) Parent Unit (display)
1. Connect the small plug of the power adapter to the parent unit and the other end to
the mains socket.
2. The blue LED will illuminate, indicating the battery is charging.
3. Then switch the positioning button to the “ON” position.
Note: For optimal battery capacity and life, it is essential to fully charge the parent unit
before using it for the rst time without connection.
3
SETUP AND FUNCTIONS:
– When the parent and baby units are switched on and within range, a live image from the
camera will appear within a few seconds.
– Place the camera in a suitable location and adjust the camera lens until you are satised
with the image on the parent unit.
Note: Do not place the baby unit within baby's reach. If there is interference on the picture
or sound, try moving the units to dierent locations, and ensure they are not close to other
electrical equipment that may interfere with the transmission.
Display
1. Signal strength
2. Camera 1 (default camera)
3. Camera 2 (additional camera)
4. Temperature*
5. Lullabies
6. Alarm clock
7. VOX mode
8. 2x zoom
9. Battery status
10. Microphone
11. Date and time
Note: *The baby monitor thermometer is not certied and the temperature data should
only be used as a general guideline.
Range
When the distance between the baby and parent unit is too far, the signal may be interrup-
ted and the image and sound may become frozen. If there is a connection loss due to the
units being out of range, a black screen is displayed and the message “Connecting…”.
:Parental unit will try to reconnect to the camera.
Note: If the they do not reconnect even after the units have been brought within range,
try to pair the units again, see the following section „Menu - 1. Camera - 1. Add Camera“.
Powering a video baby monitor via a power bank
A TrueLife video monitor is primarily intended for home use and to be powered from the
mains. Do not use VOX power saving mode when using a power bank. In this mode, the
electrical consumption of the camera (baby unit) is so low that some power banks might
think the device is charged and turn o automatically. This will interrupt transmission.
19:27 15/02/2024 Thu
21.7 °C
VOX
1 2 3 4 5 6 7 8 9
1 2
x1
10 11
4
MENU:
The Menu is accessed by pressing the OK button on the parent unit and then moving with
the „up“ and „down“ arrows and in specic settings with the „VOX“ and „ZOOM“ buttons
up and down. The „back“ button takes you back one level or to the camera preview.
The menu contains 6 icons:
1. Camera
2. Alarm
3. Settings
4. VOX
5. Language
6. System info.
• 1 – Camera
1. Add camera (repair and add 2nd camera)
The parent and baby units are already paired from the factory. If you need to re-pair the
camera, select camera 1 and conrm its re-pairing. Then press the reset button on the
back of the camera. If the pairing is successful, the message „Pairing was successful!“ will
appear. If you add a second camera, proceed in the same way.
2. View the camera
In this interface, you can choose whether you want to watch the image from camera 1
or camera 2 only. Choose „Camera Switching“ to choose automatic switching between
cameras. You can also switch between the cameras by long pressing the OK button or the
back button while viewing the image.
3. Switching delay
If you select „Camera switching“, you can choose the switching time between two came-
ras (10, 15, 20 and 30 seconds) in this interface.
4. Delete the camera
Unpairing camera 1 or camera 2.
5. Camera status light
Here you can manually turn o, turn on, or choose to automatically turn on and o the
blue power indicator LED that lights up on the camera.
6. Communication volume
Decrease or increase the volume coming from the camera when using the microphone.
7. Lullabies
Selection of lullaby 1-8 or automatic switching.
• 2. – Alarm
After choosing and setting the notication time, choose repetition (once or every day).
• 3. – Settings
1. LCD backlight - brightness setting.
2. Time and date – setting the time, date and their format.
3. Temperature unit – set the temperature unit to Celsius and Fahrenheit.