-50% na wybrane usługi i 100 dni na zwrot!
Znaleziono w kategoriach:
VDP-45A3 ALPHA
PL
EN
DE
ES
FR
IT
RU
EN VIDEO INTERCOM ............................................. 4
DE VIDEO-TÜRSPRECHANLAGE .................................9
ES VISIOPHONE ..............................................................14
FR VISIOPHONE ...............................................................19
IT VIDEOCITOFONO ..................................................... 24
RU ВИДЕОДОМОФОН ................................................ 29
PL WIDEODOMOFON ........................................... 34
4 EN
General rules for safe use of the product
Please read this instruction manual carefully before installing, connecting and using the device. In case of any diculties with the understanding of its
contents, please contact the vendor of the device. Independent installation and start-up of the device is possible, provided that proper tools are used.
However, it is recommended that the installation of the device is performed by qualied personnel.
The manufacturer bears no liability for damage that can result from improper installation and use of the detector and from independent repairs and
modications.
Please remember to:
-use the device in accordance with its intended purpose and keep it away from moisture and re,
-do not dispose of in re, do not strike, crush or expose to mechanical impact,
-do not clean the device with water or solvents and other chemicals,
-only clean the casing of the device when the power supply is switched o (you can use a damp cloth for this purpose, but wait until the casing is
completely dry aerwards)
-do not carry out modications or repairs yourself,
Note: Devices with an ingress protection rating greater than or equal to IP44 may be installed outdoors (e.g. doorbell switch buttons, video-intercom
external cassettes, cameras, etc.). Information on the penetration rate is included in the technical specications of the device.
DESIGN AND INSTALLATION OF THE VIDEO INTERCOM
1. SYSTEM DESIGN
The VDP-45A3 video intercom consists of:
- the indoor module (monitor) for indoor installation,
- the outdoor module, including the camera for installation at the gate or front door,
- DC power supply unit.
The system can be powered with 12V DC by a power supply unit installed on a DIN rail.
12 34
Gong melody selection button Installation frame for suspending
the module to the wall
63 mm
123
1
43
4
Door bell volume switch
Image brightness adjustment
Colour saturation adjustment
Volume adjustment
1. Preview button
2. Door/gate opening button (electromagnetic bolt release)
3. Conversation button
4. Microphone
1. Brackets
for attaching the indoor module to the installation frame
2. Speakers
3. Connection terminals
4. 12V DC power supply unit terminal connection outlet
2
2
1
11
Fig. 1. Monitor design
1. Protective canopy
2. Microphone
3. Dusk sensor
4. Colour camera
5. LEDs (white light)
6. Call button
7. Speaker
1
2
3
4
5
7
6
Fig. 2. Outdoor box design
EN 5
2. SYSTEM INSTALLATION
NOTE:
Recommended cross sections of wires connecting both modules depending on the distance between them: 0 - 50m 4x0.5mm2
50m - 100m 4x0.75mm2
The connection to the electromagnetic bolt should be made with a 2x0.75mm2 wire. The optimum solution will be to use one 4-core wire to connect the
monitor to the outdoor box, one 2-core wire to connect the outdoor module to the electromagnetic bolt. If the user’s connection wires are different from the
recommended wires, it is permissible to use them, however a test connection of the system is required to check it for proper operation.
2.1. OUTDOOR MODULE (MONITOR) INSTALLATION
NOTE
It is recommended to screw the monitor installation frame to a previously seated Ø60 mm ush mounting box.Improper attachment of the installation
frame could have an adverse impact on proper operation of the monitor. Avoid suspending the monitor to the frame by force. The ush mounting box is
not included.
1. Screw the included mounting frame (g. 3a) of the module to the wall/ush mounting box so as to enable easy and clean routing of the system connection wire
and power supply wire. The standard height, at which the centre of the monitor should be placed aer suspending to the frame is approx. 145 cm, however it can
be positioned according to the individual user needs.
12 34
acd
bFig. 3
2. Connect the individual wire cores to the connection terminals in the rear of the monitor (g. 3b) according to the diagram (g. 6).
3. Connect the included power supply plug to the power supply unit outlet (g. 1).
4. The rear part of the monitor enclosure features 4 openings (g. 1) used to suspend this module to the installation frame. Gently suspend the monitor to the frame
according to the direction indicated by the arrow in g. 3c so that all 4 frame brackets are in the openings in the enclosure.
5. Connect the power supply unit to the ~230V/50Hz mains.
2.2. OUTDOOR MODULE (CAMERA) INSTALLATION
The outdoor module is manufactured suitable for surface mounting.
NOTE:
Proper placement of the outdoor camera module determines the comfort of work with the device. Thus, before drilling installation opening, it is recommended
to select the place for installation through testing. For this purpose install the monitor by connecting it (according to the instruction manual) to the camera, which
should be held by another person during the tests. Connect the mains power supply and proceed to the selection of the proper place for installation of the camera.
The person holding the camera shall simulate normal activation of the device by calling the other person, located at the monitor, by pressing the button (g. 2). At
the same time, the person at the monitor shall observe the eld of view of the camera. The person holding the camera module shall set it in the optimum position,
based on the suggestions of the other person. Mark this position and only aerwards proceed to the drilling of installation opening.
50 cm
50
o
50 cm
50 cm
150-160 cm
62o
Fig. 4
SS
SS
Fig. 5
